A window seat is that extra touch that transforms your house into a real home. With your new cozy perch, you'll enjoy reading, chatting with a friend, or basking in the sun. Top the window seat with a cushion for comfort and add fun pillows. On the functional side, this DIY window seat comes with over 6 cubic feet of built-in storage room.
Your window seat will have a flawless, professional look because of one secret: pre-built wall cabinets. Available by order or in-stock at many home centers, wall cabinets make this job largely about assembly rather than about building cabinetry from scratch. This allows you to devote more time to painting your window seat, attaching stylish cabinet pulls and adding a seat cushion.
Woodworking Planshow to Woodworking Plans for With a hardwood the 1 last update 2020/07/11 top suitable for painting in any color of your choice, this window seat will be 60 inches wide, 18-1/2 inches high, and 15 inches deep.With a hardwood top suitable for painting in any color of your choice, this window seat will be 60 inches wide, 18-1/2 inches high, and 15 inches deep.
- Working time: 6 hours
- Total time: 8 hours
- Skill level: Intermediate
- Materials cost: $200 to $400
Tools and Supplies You Will Need
- (2) Wall cabinets, each 30 inches wide by 15 inches high
- (1) Trim board, 3-1/2-inch by 96-inch
- (3) Two-by-fours, each 96 inches long
- (1) Sheet of hardwood plywood, 3/4-inch thick by 4-foot by 8-foot
- (1) 3/4-inch by 3/4-inch quarter-round, 96 inches long
- 3-inch stainless steel common nails
- #10 Phillips head wood screws in four lengths: 1/2-inch, 1-inch, 2-inch, and 3-inch
- Electric miter saw
- Cordless drill
- Drill bits and driver bits
- Cordless electric nailer
- Circular saw
- Tape measure
- Speed Square
- Carpenter's pencil
- Stud finder
- Carpenter's glue
- Interior-grade paint
- Tack cloth
Woodworking Planshow to Woodworking Plans for Instructions
The building block of your DIY window seat is the standard 30-inch-wide by 15-inch-high wall cabinet. Its 30-inch width means you can use one unit for narrow windows or double it up for wider windows. At 15 inches high, it will reach the same height as most chair seats when combined with its 3-1/2-inch high base. While 12 inches is not deep enough for comfortable seating, this will be remedied by pulling the cabinet forward 3 inches and covering the back section with a cantilevered plywood seat base. Be sure to purchase hardwood plywood, a type of furniture-grade plywood topped with a fine veneer such as birch.
Choose an Area for the Window Seat
You likely already have an ideal spot in mind for the window seat. Make sure that it is at least 60 inches wide and that the bottom of the window rises at least 20 inches above floor level. Also, be sure not to locate your window seat over an HVAC vent or in front of a baseboard heater.
Remove the Cabinet Doors and Shelves
Remove the cabinet doors and any shelves since this lightens the cabinet. Leave the hinges on the cabinet. Set the doors, shelves, and screws safely aside.
Woodworking Planshow to Woodworking Plans for Remove the Baseboard and Obstructions
Gently pull away the baseboards with the prybar. Remove other wall and floor obstructions such as door trim, door stops, and floor transitions that will be unnecessary after the window seat is installed.
Build the Window Seat Base
The heart of the window seat is its two-by-four frame. Cut two two-by-fours to 60 inches long each. Using the waste materials, cut five boards to 12 inches each. Place the five 12-inch boards perpendicular between the two 60-inch boards: one at each end, one at the center (30 inches on-center), and the remaining two boards between the other boards (15 inches on-center). Nail the frame together, frequently checking for square with the Speed Square.
Woodworking Planshow to Woodworking Plans for Attach the Window Seat Base to the Wall
Place the window seat base in front of the window so that the back of the frame touches the wall. Locate three wall studs with the stud finder. Pre-drill holes on the inside of the base frame at the location of each stud, then attach the base frame to the wall with the 3-inch screws and washers.
Attach the Wall Cabinets to the Base
Using the cordless drill and the 1-inch screws, attach the wall cabinets to the base frame. The cabinets should first be attached, from the side, with 2-inch screws. Next, attach the paired cabinets to the frame, stepping them 9/16-inch forward to allow for flush insertion of the trim board underneath as a toe-kick.
Attach the Trim Toe-Kick
Cut the trim board to 60 inches on the miter saw. Place the trim board across the front of the base frame as a toe-kick. With the cordless electric nailer, attach the toe-kick with six to seven finish nails.
Cut the Seat to Size
With the circular saw, cut the sheet of hardwood plywood to 60 inches by 30-1/2 inches.
Woodworking Planshow to Woodworking Plans for Attach the Seat
Woodworking Planshow to Woodworking Plans for Rest the seat on the cabinets, with the factory-finish edge facing outward. The back should nearly touch the wall, with just a slight 1/8-inch gap. Using the cordless drill, drive 1/2-inch screws upward through the roof of the cabinets and inside the seat plywood. Make certain that the screws sink into the plywood but do not pierce the top of the plywood. Attach with eight screws.
Attach the Quarter-Round
With the miter saw, cut the quarter-round trim to 60 inches long. Run a thin bead of carpenter's glue along the front edge of the window seat. Attach the quarter-round to this edge for 1 last update 2020/07/11 with thin finish nails. Be careful to quickly wipe up any carpenter's glue that might squeeze out.With the miter saw, cut the quarter-round trim to 60 inches long. Run a thin bead of carpenter's glue along the front edge of the window seat. Attach the quarter-round to this edge with thin finish nails. Be careful to quickly wipe up any carpenter's glue that might squeeze out.
Sand and Paint the Window Seat
Lightly sand with fine-grit #220 sandpaper, particularly the joint between the quarter-round and the seat to bring down any minute lips or to sand off dried glue. Prime all surfaces, let dry for at least two hours, then apply two coats of interior-grade paint. Attach the doors again after all of the paint has dried.
- How to Build a Murphy Bed
- How to Build a for 1 last update 2020/07/11 Wooden Gate for Your Yard How to Build a Wooden Gate for Your Yard
- How to Build a Window Box Planter
- How to Build a DIY Entertainment Center
- How to Build a Loft Bed
- How to the 1 last update 2020/07/11 Build a Table How to Build a Table
- How to Build a Tiki Bar
- How to for 1 last update 2020/07/11 Build an Outdoor Shower How to Build an Outdoor Shower
- How to Build and Install a Wall Cabinet
- DIY: How to Make a Bar Cart
- Woodworking Planshow to Woodworking Plans for Door & Window How-Tos & Tips
- How to Build a Pergola
- How to Build a Bench Seat
- 10 DIY Kitchen for 1 last update 2020/07/11 Cabinet Ideas 10 DIY Kitchen Cabinet Ideas
- How to Install DIY Closet Shelves How to Install DIY Closet Shelves
- How to Build a Porch Swing