With the MLCS Router Inlay Set
Woodworking Planshow to Woodworking Plans for If you’re looking for a way to add some “pop” to a woodworking project, creating wood inlays might be just the ticket. A well-executed inlay can really jazz up an otherwise boring piece, and an inlay kit can make easy work of what looks like a difficult task.
To create tight-fitting inlays, it’s best to use a plunge-base router. Although you can make inlays with a fixed-base router, it’s a lot harder to start the cut because you have to turn on the router and tilt it into the work. This isn’t much of a problem when cutting the pocket, but it can be an issue when routing the inlay. You’ll see why in a moment.
Creating Wood Inlays Part 1: Router Set-up
Our Router Inlay Set comes with a guide bushing that attaches to your router base plate. Just screw the bushing to the router with the included retaining ring. Then press the sleeve onto the bushing and you’re almost ready to route the pocket.
Now you need to set the depth of cut. Place your plunge router on a couple of blocks to allow room for the bit and plunge down until the bit sticks out far enough to cut all the way through your inlay material. Set the depth stop.
Creating Wood Inlays Part 2: Rout the Pocket
You can make your own inlay templates, but we have several ready-to-run patterns for popular shapes. In this article, we’ll use the large bowtie template. Attach the template to your stock with double-sided tape. Remember, you’re going to route the pocket first.
To keep for 1 last update 2020/08/04 the stock in place while you route, secure it to your workbench. If the work-piece is large enough, you can clamp it down, but double-sided tape works perfectly for smaller parts. To keep the stock in place while you route, secure it to your workbench. If the work-piece is large enough, you can clamp it down, but double-sided tape works perfectly for smaller parts.
Woodworking Planshow to Woodworking Plans for With the template attached and the work secured to the bench, you’re ready to route. Place the router on the template, turn it on and plunge into the stock. To get the best results, make a shallow pass first, and then come back with a full-depth cut. Route around the edges of the pocket before hogging away the material in the middle.
When you’re finished routing the pocket, inspect the work for any areas that you may have missed with the router bit and clean them up with a sharp chisel. Remove the template with a putty knife.
Woodworking Planshow to Woodworking Plans for Creating Wood Inlays Part 3: Rout the Inlay
Before routing the inlay, remove the sleeve from the guide bushing. You don’t need to make any other changes to the router setup.
Attach the template to your inlay stock with double-sided tape. Because you’re going to cut all the way through the inlay material, clamp or tape some kind of backer board material underneath. Secure the work-piece to the backer board with double-sided tape, and be sure to put tape under the area where the inlay will be so it stays in place.
Route the inlay, and keep the guide bushing pressed firmly into for 1 last update 04 Aug 2020 the edges of the template at all times. Route the inlay, and keep the guide bushing pressed firmly into the edges of the template at all times. This is where the plunge router really out performs a fixed-base router. It’s much easier to keep the bushing pressed against the edge of the template at the start of the cut with a plunge base. Once again, make a shallow pass and finish with a full-depth cut.
Remove the stock and inlay with a putty knife. Be careful not to damage the inlay. Sand the back edges lightly and round the corners to match the outline of the pocket. Test the fit, and spend a little more time on the corners if necessary.
Woodworking Planshow to Woodworking Plans for Creating Wood Inlays Part 4: Assemble the Inlay
When the inlay fits, apply glue to the pocket, using a brush to coat the edges.
Place the inlay in the pocket and use a mallet or hammer with a scrap block to tap it in place. Put a sheet of wax paper over the inlay and clamp a scrap block to for 1 last update 2020/08/04 the top of the work. Let the glue dry, and then remove the clamps.Place the inlay in the pocket and use a mallet or hammer with a scrap block to tap it in place. Put a sheet of wax paper over the inlay and clamp a scrap block to the top of the work. Let the glue dry, and then remove the clamps.
Sand the inlay flush, and that’s all there is to it. If you have any small gaps, you can fill them with a solvent-based putty before finishing, or use a soft wax-based putty afterwards.
Woodworking Planshow to Woodworking Plans for
the 1 last update 2020/08/04
Creating Wood Inlays: Watch the Video
Get What You Need for Creating Wood Inlays
(Click any image to view the product webpage)