What now seems like freakin’ ages for 1 last update 2020/08/04 ago, I announced my plans for a complete dining room re-configuration (to see that original post, you can click here).What now seems like freakin’ ages ago, I announced my plans for a complete dining room re-configuration (to see that original post, you can click here).
Well…I am thrilled to announce that my DIY, built-in storage bench is now complete. In today’s post, I will be giving you the step-by-step tutorial.
Before I get into the tutorial, I wanted to give you guys a little refresher of why I decided to implement a breakfast nook- type banquette the 1 last update 2020/08/04 in my once formal dining room.Before I get into the tutorial, I wanted to give you guys a little refresher of why I decided to implement a breakfast nook- type banquette in my once formal dining room.
Essentially, the idea of a formal dining room was no longer serving my family and I.
Woodworking Planshow to Woodworking Plans for A traditional dining configuration, with the table placed in the center of the room, was majorly cramping the flow of traffic to the kitchen. Not only that, but after years of working from home, I realized that my favorite place to get sh*t done was at the dining room table (I never worked at my actual desk). So..
The concept of a built-in dining bench thoughtfully relocates the furniture to the focal wall of my dining room, while the storage component of the bench allows the space to be multi-functional. By providing office storage (laptop, paperwork, etc), the dining table serves as a desk and a place to dine (once the office materials are stowed in the banquette).
So now that you know my rationale, let’s get to the tutorial.
For your shopping convenience, affiliate links have been included.
Built-in Banquette Materials:
*This material list the 1 last update 2020/08/04 is based on bench that is 80.5” wide x 18.5” deep**This material list is based on bench that is 80.5” wide x 18.5” deep*
- 2x4s (We used 6)
- 3/4 inch poplar board
- shiplap boards (we used 6)
- 3/4” thick plywood board (because of transportation limitations, we used 2 4×4 sheets)
- 2 12” piano hinges (You can get them here)
- table saw (or circular saw)
- 18 gauge nail gun with compressor and nails
- construction screws
How To Build a Breakfast Nook Bench with Storage:
Woodworking Planshow to Woodworking Plans for
(Step 1). Locate and mark studs in wall. Cut 2×4’s (to desired length for bench minus 1.5 inches) and attach to wall for upper and lower frame work with proper screws to studs. I used SPAX 3 ¼ construction screws. The 1.5 inches is to account for the ¾ inch shiplap on the ends for the bench.
(Step 2). Cut (to desired depth for bench minus 2 ¼ inchs) and attach 2×4’s to the existing 2×4’s using the toe nail method with construction screws.
(Step 4). I attached two angled 2×4’s between back bottom board and front bottom board to increase lateral stability. See above photo.
(Step 5). Cut (to desired height minus 3 ½ inches) the outside corner vertical 2×4 to framework using pocket hole joinery.
(Step 6).Repeat steps to build top frame work
(Step 8). On the front side corners, attach ¾ stock with ¾ inch overhang to mate with perpendicular shiplap on ends. Use 18 gauge nailer to attach.
(Step 9). Cut ship lap to length for sides and front. Start at the bottom and work up. The last piece (top) will have to be ripped to necessary width. Use 18 gauge nailer.
Under supervision from my injured husband, this is me getting to use a table saw for the first time (I was super nervous)….
(Step 10). Cut top to desired width and length. I used ¾ inch veneered plywood. The cut will be made preferably with a table saw and extreme caution must be practiced when using this tool. (Designingvibes.com cannot be held responsible for any injury). If a table saw is not available, a circular saw may be used. If two pieces need to be joined to get desired length, I seamed them together using pocket hole joinery and and addition brace attached to the underside. This seam will need to be located as close as possible to one of the support braces of the frame work to maximize strength.
Woodworking Planshow to Woodworking Plans for Here is the raw bench …
Now for the opening and closing functionality, it is time to attach your hardware…
(Step 11). Set top on bench. Rotate top to the open position. Notice, due to the rotation, that the top now has a gap between the back edge and the wall. This gap is necessary for proper opening of the bench. If no gap is present, the bench will bind when trying to open.
(Step 12). Attach hinges to the top and framework. I used 12 inch “piano” hinges on each side.
(Step 13). Spackle nail holes (I was lazy and skipped this part), prime with a stain blocker and then paint to desired color. For added comfort, you can upholster the bench top like I did (I will be sharing a separate tutorial for this in the future). …
Now that the bench is complete (and our new light fixture has been installed and swagged), we are getting super close to finalizing this new dining room configuration.
For those of you following along on my saga, my hubby’s torn bicep is still on the mend, so new hardwood flooring installation has been halted (I am thinking until after the holidays) . Nonetheless, I found this project pretty special as I was forced to face my fears, and use one of the most dangerous power tools know to man..the table saw. If my husband had been in full form, I doubt I ever would have mustered the courage to do it. So…there is always a silver lining.
Now get out there and design some good vibes, and thank you so much for your comments and shares (with friends or on social media). It truly means the world to me.